PERMATEX

Product categories

Product tags

Brands

Marine Grez-Off® Heavy Duty Degreaser

Cleaners & Degreasers

Features and Benefits:

#1 Rated Marine Degreaser by Powerboat Reports. A biodegradable, non-solvent heavy-duty degreaser that easily cuts through oil, grease and grime. Cleans and dissolves heavy soils on inboard & outboard motors, machinery and dock equipment. Also recommended for bilge cleaning. Marine Grez-Off® is VOC compliant, non-flammable and non-combustible.

DIRECTIONS:

Some surfaces such as aluminium alloys, plastic or painted surfaces are inherently sensitive to alkaline cleaners.
Spot test on ALL surfaces before use.
Do not use on motorcycles or glass.
Use with adequate ventilation. Do not inhale mist.
The use of safety glasses and rubber gloves is recommended.
These directions must be followed or damage may result.

For Cleaning:

Before degreasing, be sure that all surfaces are cool to the touch. Do not apply in direct sunlight or if air temperature is above 100°F.
Spray MARINE GREZ-OFF full strength onto the cool, pretested surface to be degreased.
Allow MARINE GREZ-OFF to penetrate the soil. NEVER allow MARINE GREZ-OFF to dry on any surface. Stubborn soils may require brushing or a second application.
Immediately rinse with water until no sudsing is noticeable.

Automobile
Suggested Applications: Inboard and outboard motors, machinery, and dock equipment.

Marine
Suggested Applications: Inboard and outboard motors, bilges, machinery, docks and mooring equipment, trailers and tools.

View Marine Grez-Off® Heavy Duty DegreaserSDS Here

Marine Spray Nine® Heavy-Duty Cleaner + Degreaser + Disinfectant

Cleaners & Degreasers

Features and Benefits:

Suited for cleaning electrical and electronic devices, this fast evaporating, noncorrosive cleaner leaves no residue. It removes grease, dirt, oil, flux and other surface contaminants. Designed to be an alternative to CFC-113, 1,1,1-trichloroethane and perchloroethylene solvents.

DIRECTIONS:

DISINFECTING:
When used as directed, Marine Spray Nine Heavy-Duty Cleaner + Degreaser + Disinfectant will disinfect hard,non-porous surfaces such as countertops, stainless steel, tables, walls and floors.

*Marine Spray Nine kills Norwalk/Norovirus-ATCC VR-782, Influenza A2 Virus-ATCC VR-544,Coxsackie B3 Virus-ATCC VR-30 and Rhinovirus Type 37-ATCC VR-1147 in just 30 seconds!It is a violation of Federal law to use this product in manner inconsistent with its labeling.

Outdoor surfaces subjected to severe weather conditions, especially U.V. exposure, may be particularly sensitive to alkaline cleaners. Follow the outdoor surface manufacturer’s recommended cleaning instructions.

Always test on a small area of surface to be cleaned and air-dry completely to determine colorfastness and surface integrity. Do not use on wool, leather, glass, untreated wood, treated fabric or weathered surfaces. Do not use this product in combination with caustics, acids or bleach.

TO CLEAN:

Spray on soiled surface.
Wipe thoroughly with a clean, damp sponge/cloth or rinse.(Do not allow to dry on surface)
For assistance with specific cleaning problems, call 1-800-477-7299.Note: Heavy deposits, stubborn soils and stains may require scrubbing or additional applications.

TO DISINFECT/DEODORIZE:

Clean surface as instructed above.
Repeat application making sure to wet all surfaces thoroughly.
Allow to stand for 45 seconds (30 seconds for viruses) minimum.
Wipe thoroughly with a clean, damp sponge/cloth or rinse.
When used on food contact surfaces such as counters and tables,rinse thoroughly with potable water. Do not use on dishes,glasses or silverware.

TO CONTROL MOLD & MILDEW on precleaned, hard, non-porous surfaces:

Spray thoroughly, making sure to wet surface completely. Allow to stand for 3 minutes. Wipe off with a clean, damp sponge or cloth and rinse thoroughly. Reapply as necessary.

Marine
Suggested Applications: Boats, hulls, fiberglass, galleys, boat covers, jet skis, camping equipment, RVs, trailers, personal watercraft, awnings, coolers, inflatables, life jackets, vinyl and bait buckets.

View Marine Spray Nine® Heavy-Duty Cleaner + Degreaser + Disinfectant SDS Here

Permatex® 1 Minute Gel Epoxy

Epoxy & Adhesives

Features and Benefits:

Permatex® General Purpose 1 Minute Gel Epoxy is a fast setting, two-part adhesive and filler system specially formulated with a Blue Dye Indicator that disappears when it’s fully mixed and ready to use. The advanced gel formulation reduces mess and waste compared to traditional epoxies; unique indicator system takes the guesswork out of “ready to use”.

Non-drip formula allows for mess free application
Can easily be applied to overhead and hard to reach places
Sets in just 1 minute/Cures in 5 minutes
Blue dye indicator disappears when epoxy is ready to apply
No clamping required
Bonds to metals, hard plastics, ceramics, and more!
PSI Strength: 2,500

DIRECTIONS:
PROTECT: Work area must be protected from accidental spills.
CLEAN: Surfaces must be clean, dry and free of grease and oil.
PREPARE: Roughen smooth surfaces (using abrasives or sandpaper).
OPEN PACKAGE: Remove Syringe. Turn syringe nozzle end up and pull plunger back slightly (1/8”). Allow air bubbles to rise to top. Snap off and save storage cap. Push plunger to dispense equal amounts of hardener and resin onto discard-able surface such as a piece of cardboard. Mixing paddle will pop out from plunger. Pull back plunger to stop flow. Snap cap back on.
MIX QUICKLY: Quickly and thoroughly mix until blue colour turns clear (about 15 sec).
APPLICATION: Apply small amount of mixture to both surfaces and assemble parts immediately (product sets in approximately 60 seconds). Remove any excess epoxy immediately.
CURE TIME: Usable strength is reached in 1 hour at 72ºF (22ºC).Cooler temperatures may require longer set time.
CLEAN-UP: Attach nozzle cap and store in moulded tray.
NOTE: Adhesive will not bond most polyethylene or polypropylene plastics.

Automobile
Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including, ceramic, chrome, fabric, fiberglass, glass, hard plastic, and metal and rubber.

View Permatex® 1 Minute Gel Epoxy SDS Part One Here

View Permatex® 1 Minute Gel Epoxy SDS Part Two Here

View Permatex® 1 Minute Gel Epoxy Product Information Here

Permatex® 2 Ton Epoxy

Epoxy & Adhesives

Features and Benefits:

Permatex’s Clear 2 Ton Epoxy is a general-purpose high strength epoxy designed to bond together ridged materials for a permanent hold. Repositionable up to 15 minutes and is clear in color. Bonds ceramics, fiberglass metal concrete, and more!

Repositionable high strength adhesive; bonds together rigid materials
Sets in 30 minutes / Cures in 1 hour for multiple repairs
Specially formulated for high clarity and impact strength
Gap-filling and non-shrinking formula
Resists salt solution, unleaded gasoline, mineral spirits, oil and anti-freeze
PSI Strength: 3,400

DIRECTIONS

For best results: Roughen, remove any grease and oil, clean and dry surfaces to be joined or repaired.
Remove plastic mixing paddle from center of black plunger. Turn nozzle end up and pull plunger back slightly (1/8″).
Allow air bubbles to rise to top. Snap off and save storage cap.
Push plunger evenly to dispense equal amounts of hardener and resin onto a discardable surface such as a piece of cardboard or the plastic container on the front of this package. Pull back plunger to stop flow.

MIX THOROUGHLY with paddle provided. Epoxy has a working time of 30 minutes.
Apply to surfaces to be joined or repaired. Epoxy will fixture in 1 hour and fully cure in 24 hours. Wipe nozzle clean. Replace cap for storage.
NOTE: Will not bond to polyethylene or polypropylene plastics. This epoxy product is recommended for indoor use only, as the cured epoxy can yellow and darken when exposed to sunlight and the elements.

Suggested Applications: Ceramics, fiberglass, metal, concrete & more!

View Permatex® 2 Ton Epoxy SDS Part One Here

View Permatex® 2 Ton Epoxy SDS Part Two Here

View Permatex® 2 Ton Epoxy Product Information Here

Permatex® 30 Minute High Strength General Purpose Epoxy

Epoxy & Adhesives

Features and Benefits:

Versatile, easy-to-use, general purpose epoxy adhesive is two-part adhesive and filler system that eliminates the need for welding or brazing. Sets in thirty minutes, no clamping needed. Clear appearance. Fills gaps and will not shrink. When cured, can be drilled, sanded, threaded or filed. Resistant to water and solvents. Temperature range -60°F to 180°F (-51°C to 82°C). Permanent strength up to 3500 PSI.

DIRECTIONS:
PROTECT: Work area must be protected from accidental spills.
CLEAN: Surfaces must be clean, dry and free of grease and oil.
PREPARE: Roughen smooth surfaces (using abrasives or sandpaper).
OPEN PACKAGE: Remove Syringe. Turn syringe nozzle end up and pull plunger back slightly (1/8”). Allow air bubbles to rise to top. Snap off and save storage cap.Push plunger to dispense equal amounts of hardener and resin onto discard-able surface such as a piece of cardboard. Mixing paddle will pop out from plunger. Pull back plunger to stop flow. Snap cap back on.
MIX THOROUGHLY: Thoroughly mix with paddle provided for two minutes until evenly coloured.
APPLICATION: Apply small amount of mixture to both surfaces and assemble parts immediately (product sets in approximately 30 minutes). Remove any excess epoxy immediately.
CURE TIME: Usable strength is reached in 8 hours at 72ºF (22ºC). Cooler temperatures may require longer set time.
CLEAN-UP: Attach nozzle cap and store in moulded tray.
WARNING: Adhesive will not bond most polyethylene or polypropylene plastics.

Automobile
Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including ceramic, chrome, fabric, fiberglass, glass, hard plastic, metal, and rubber.

View Permatex® 30 Minute High Strength General Purpose Epoxy Part One SDS Here

View Permatex® 30 Minute High Strength General Purpose Epoxy Part Two SDS Here

View Permatex® 30 Minute High Strength General Purpose Epoxy Product Information Here

Permatex® 5 Minute Gap Filling Epoxy

Epoxy & Adhesives

Features and Benefits:

Versatile, easy-to-use, general purpose epoxy adhesive is two-part adhesive and filler system that eliminates the need for welding or brazing. Sets in five minutes, no clamping needed. Clear appearance. Fills gaps and will not shrink. Resistant to water and solvents. Temperature range -60°F to 180°F (-51°C to 82°C). Permanent strength up to 3400 PSI. Self-mixing dual syringe (84164) blends the adhesive and filler as it dispenses, eliminating the need for manual mixing.

DIRECTIONS:
PROTECT: Work area must be protected from accidental spills.
CLEAN: Surfaces must be clean, dry and free of grease and oil.
PREPARE: Roughen smooth surfaces (using abrasives or sandpaper)
OPEN PACKAGE: Remove tubes and use the back of cap or a sharp point to puncture seals.
DISPENSE: Squeeze tubes to dispense resin and hardener. Thoroughly mix resin & hardener on a clean, discardable surface for 2 to 3 minutes until evenly colored.
APPLICATION: Apply a small amount of mixture to both surfaces and assemble parts immediately (product sets in 4-6 minutes).Remove any excess epoxy immediately.
CURE TIME: Usable strength is reached in four hours at72°F (22°C). Cooler temperatures may require longer set time.
CLEAN-UP: Attach nozzle caps and store in moulded tray.
NOTE: Adhesive will not bond most polyethylene or polypropylene plastics.

Automobile
Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including, ceramic, chrome, fabric, fiberglass, glass, hard plastic, metal and rubber.

View Permatex® 5 Minute Gap Filling Epoxy Part One SDS Here

View Permatex® 5 Minute Gap Filling Epoxy Part Two SDS Here

View Permatex® 5 Minute Gap Filling Epoxy Product Information Here

Permatex® 5 Minute Gel Epoxy

Epoxy & Adhesives

Features and Benefits:

Permatex’s General Purpose 5 Minute Gel Epoxy provides the flexibility to reposition before the setting time. The fast setting, two-part adhesive and filler system is specially formulated with a Blue Dye Indicator that disappears when it’s fully mixed and ready to use. The advanced gel formulation reduces mess and waste compared to traditional epoxies; unique indicator system takes the guesswork out of “ready to use”.

Non-drip formula allows for mess free application
Can easily be applied to overhead and hard to reach places
Sets in just 5 minutes / Cures in 10
Blue dye indicator disappears when epoxy is ready to apply
No clamping required
Bonds to metals, hard plastics, ceramics and more!
PSI Strength: 3,400

DIRECTIONS:
PROTECT: Work area must be protected from accidental spills.
CLEAN: Surfaces must be clean, dry and free of grease and oil.
PREPARE: Roughen smooth surfaces (using abrasives or sandpaper).
OPEN PACKAGE: Remove syringe. Using a sharp blade, cut off tips of both nozzles.
DISPENSE: Depress plunger to dispense resin and hardener. Thoroughly mix resin & hardener on a clean, discardable surface for 2 to 3 minutes until evenly colored.
APPLICATION: Apply a small amount of mixture to both surfaces and assemble parts immediately (product sets in 4-6 minutes).Remove any excess epoxy immediately.
CURE TIME: Usable strength is reached in four hours at72°F (22°C). Cooler temperatures may require longer set time.
CLEAN-UP: Attach nozzle cap and store in molded tray.
NOTE: Adhesive will not bond most polyethylene or polypropylene plastics.

Application: Automobile
Suggested Applications: Ideal for complex, multi-piece assemblies. Bonds rigid materials including, ceramic, chrome, fabric, fiberglass, glass, hard plastic, and metal and rubber.

View Permatex® 5 Minute Gel Epoxy SDS Part One Here

View Permatex® 5 Minute Gel Epoxy SDS Part Two Here

View Permatex® 5 Minute Gel Epoxy Product Information Here

Permatex® 500° High Heat Epoxy

Epoxy & Adhesives

Features and Benefits:

Permatex’s 500® High Heat Epoxy is the first and only high temperature liquid syringe epoxy! Ideal for surface repairs with high temperatures such as under-hood automotive & home repair. This high temperature epoxy withstands 2X higher temperatures compared to standard epoxies that traditionally breakdown at 250⁰F. Ideal for under-hood repairs where temperatures can range up at 400⁰F on a hot summer day.

Seal against many liquids, gasses and common automotive fluids
Ideal for under-hood automotive applications
Eliminates need to weld or braze
Sets in 10 minutes/ Cures in 2 hours
Bonds to metals, hard plastics, ceramics, glass rubber and more!
PSI Strength: 2,500

Suggested Applications: Furniture, doors, windows, trim/moulding, decks & more!

Directions:

For best results: Roughen, remove any grease and oil, clean and dry surfaces to be joined or repaired.
Remove plastic mixing paddle from center of black plunger. Turn nozzle end up and pull plunger back slightly (1/8″). Allow air bubbles to rise to top. Snap off and save storage cap.
Push plunger evenly to dispense equal amounts of hardener and resin onto a discardable surface such as a piece of cardboard or the plastic container on the front of this package. Pull back plunger to stop flow.

MIX THOROUGHLY with paddle provided. Epoxy has a working time of 10 minutes.
Apply to surfaces to be joined or repaired. Epoxy will fixture in 2 hours and fully cure in 24 hours. Wipe nozzle clean. Replace cap for storage.
NOTE: Will not bond to polyethylene or polypropylene plastics.

View Permatex® 500° High Heat Epoxy SDS Part One Here

View Permatex® 500° High Heat Epoxy SDS Part Two Here

View Permatex® 500° High Heat Epoxy Product Information Here

Permatex® High Temperature Anaerobic Flange Sealant

Permatex® Anaerobic Flange Sealant

Gasketing

Features and Benefits:

Flexible, gasketing material for use on rigid machined flanges with less than .015″ gap. OEM approved use where OEs specify “anaerobic” gasket (cures in the absence of air). Withstands temperatures to 300°F (149°C). Eliminates preformed, pre-cut, paper, rubber and cork gaskets. Flexes with flanges that move in service.

DIRECTIONS:

TO MAKE A GASKET:

Clean both flange surfaces. Remove paint, dirt, grease or old gasket completely.
Spray Permatex^® Surface Prep^™ activator on one surface only. Allow to dry 1-2 minutes.
Apply a continuous bead of sealant to the unprimed surface.
Assemble mating surfaces with minimal lateral movement. Excess sealant can be wiped awaywith a cloth and shop solvent.

TO DRESS A GASKET:

Clean both flange surfaces. Remove paint, dirt, grease or old gasket completely.
Spray Permatex^® Surface Prep^™ activator to both flange surfaces. Allow to dry 1-2 minutes.
Completely cover both sides of the precut gasket with sealant.
Place coated gasket on flange, and assemble mating surfaces with minimal lateral movement.

Automobile:

Suggested Applications: Water pumps, thermostat housings, transmission pans, transmission case covers, engine cases, timing covers, and transaxle casings.

View Permatex® Anaerobic Flange Sealant SDS HERE

View Permatex® Anaerobic Flange Sealant Product Information HERE

Permatex® Anaerobic Gasket Maker

Gasketing

Features and Benefits:

OEM specified. Noncorrosive gasketing material designed primarily for use on aluminum, iron, and steel flanged mating surfaces. Ideal for on-the-spot and emergency repairs, or when a conventional gasket is unavailable. Fills gaps up to .015″ and cures to a solvent-resistant seal that will not tear or decay during service. Parts disassemble easily even after extended service. Old gasket material can be removed in minutes with a simple putty knife.

DIRECTIONS:

TO MAKE A GASKET:

Clean both flange surfaces. Remove paint, dirt, grease or old gasket completely.
Spray Permatex^® Surface Prep^™ activator on one surface only. Allow to dry 1-2 minutes.
Apply a continuous bead of sealant to the unprimed surface.
Assemble mating surfaces with minimal lateral movement. Excess sealant can be wiped away with a cloth and shop solvent.

TO DRESS A GASKET:

Clean both flange surfaces. Remove paint, dirt, grease or old gasket completely.
Spray Permatex^® Surface Prep^™ activator to both flange surfaces. Allow to dry 1-2 minutes.
Completely cover both sides of the precut gasket with sealant.
Place coated gasket on flange, and assemble mating surfaces with minimal lateral movement.

Automobile:

Suggested Applications: Water pumps, thermostat housings, transmission pans, transmission case covers, engine cases, timing covers, and transaxle casings.

View Permatex® Anaerobic Gasket Maker SDS HERE

View Permatex® Anaerobic Gasket Maker Product Information HERE

Permatex® Anti-Seize Lubricant

Lubricants

Features and Benefits:

A highly refined blend of aluminium, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-51°C to 871°C). Salt, corrosion and moisture resistant ideal for marine use. Non-aerosol version meets Mil Spec #907E. Aerosol – Level 3*

DIRECTIONS:

For best results, part surfaces must be clean and free of grease.
Apply a light coating of product to parts.
Assemble parts.
Wipe away any excess compound.

Automobile:

Suggested Applications: For easy removal of spark plugs, cylinder head and exhaust head bolts; apply to anchor pins on brake assemblies, u-bolts and spring bolts, hinges, gears, chain, sprockets and rollers.

Motorcycle:

Suggested Applications: Axle assembly

Heavy Duty:

Suggested Applications: Prevents seizing and galling of all metals on chassis and engines. Withstands temperatures up to 1600°F.

Marine:

Suggested Applications: For easy removal of spark plugs, cylinder head and exhaust head bolts

Package Sizes: 8 oz. brush-top bottle, 1 oz. tube carded, 12 oz. aerosol can 8.5 oz. net wt., 4 oz. bottle, 16 oz. brush-top bottle

View Permatex® Anti-Seize Lubricant SDS HERE

View Permatex® Anti-Seize Lubricant Product Information HERE

Permatex® Automatic Transmission RTV Gasket Maker

Gasketing

Features and Benefits:

OEM specified. Developed with U.S. automotive OEMs and complies with extended warranty requirements. It resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Benefits include improved transmission oil resistance, good adhesion while retaining flexibility, sensor-safe, noncorrosive and can be used as a gasket maker or dressing. Nonflammable, nontoxic, low odor.

DIRECTIONS:

For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex^® Brake and Parts Cleaner.
Cut nozzle to desired bead size gaskets are best formed using a 1/16″ to 1/4″ (2 to 6 mm) bead.
Apply a continuous and even bead of silicone to one surface; surround all bolt holes. Assemble parts immediately. Finger tighten bolts until material begins to squeeze out around flange. Allow to cure for one hour then retighten 1/4 to 1/2 turn.
For best results, allow to cure overnight.
Replace cap after use. Clean hands with dry cloth or Permatex^® Fast Orange^® Hand Cleaner. Clean tools with non-flammable cleaning fluid.

NOTE: Not recommended for use on head gaskets or parts in contact with gasoline.

Automobile:

Suggested Applications: Automatic transmission pans, case halves, and side covers.

View Permatex® Automatic Transmission RTV Gasket Maker SDS HERE

View Permatex® Automatic Transmission RTV Gasket Maker Information HERE

Permatex® Aviation Form-A-Gasket® No. 3 Sealant Liquid

Gasketing

Features and Benefits:

Slow-drying, non-hardening brush-top sealant approved for use in aviation as well as automotive applications. Temperature range -65°F to 400°F (-54°C to 204°C); resists gasoline, oil and grease.

DIRECTIONS:

Use brush to apply a thin, even coat to each surface. Allow to air-dry a fewminutes before fastening the parts into position. If thinning is necessary, add 188 proof denatured alcohol. For use on most types of gaskets, machined surfaces and screw thread connections of airplane and automobile engines.

Automobile:

Suggested Applications: Close-fitting machined surfaces, sealing hoses, and solid gaskets.

Marine:

Suggested Applications: Close-fitting machined surfa

View Permatex® Aviation Form-A-Gasket® No. 3 Sealant Liquid SDS HERE

View Permatex® Aviation Form-A-Gasket® No. 3 Sealant Liquid Product Information HERE

Permatex® Battery Cleaner

Parts Cleaners

Features and Benefits:

Spray it on and wash corrosion off. Works in just three minutes. Penetrates and removes corrosion, dirt and grime instantly. Cleans all types of storage batteries and attachments in emergency power supply systems. Level 1

DIRECTIONS:

Shake well. Spray corroded parts thoroughly with foaming PERMATEX Battery Cleaner.
Let stand for approximately 3 minutes.
Gently rinse with water to avoid splashing corrosion on other areas.
Wipe with a rag.

Application:
Automobile
Suggested Applications: Automotive, marine, farm machinery and motorcycle batteries, cables, and terminal connections.

Motorcycle
Suggested Applications: Battery, cables, and terminal connections.

Heavy Duty
Suggested Applications: Battery, cables, and terminal connections.

Marine
Suggested Applications: Battery, cables, and terminal connections.

View Permatex® Battery Cleaner SDS Here

Permatex® Battery Protector & Sealer

Specialised maintenance & repair

Features and Benefits:

Seals and coats battery terminals eliminating the formation of acid salt corrosion typically found when terminals are untreated. Prevents terminal corrosion and battery drain. Increases battery life and improves electrical flow. Spray on batteries, battery terminals, and cables, in or out of storage. Aerosol – Level 3*

DIRECTIONS:

First, clean parts to be treated with SA-8 (80369) Permatex^® Battery Cleaner. Shake Battery Protector well. Hold can 10 to 12 inches from the treated surface, and apply two thin coats.

Automobile:

Suggested Applications: Automotive, marine, farm machinery, and motorcycle batteries.

Motorcycle:

Suggested Applications: Motorcycle batteries

Marine:

Suggested Applications: Marine batteries

View Permatex® Battery Protector & Sealer SDS HERE

View Permatex® Battery Protector & Sealer Product Information HERE

Permatex® Belt Dressing & Conditioner

Lubricants

Features and Benefits:

Extends belt life. Penetrates the cord fibers of “V” belts to restore pliability and flexibility. Prevents belt slippage due to heat, cold, dampness, dust and glazing. Eliminates squeaking and slipping. Level 1*

DIRECTIONS:

Shake well. Attach extension tube. While engine is running, spray lightly on inner working surface of belt near smallest or upper most pulley. Allow belt to run for several minutes to condition and cure dressing. Reapply as needed. Do not spray on pulleys.

Automobile:

Suggested Applications: Fan belts, water pumps, power steering, sewing machines, washing machines, air conditioners, lawn mowers, and power tools.

Package Sizes: 16 oz. aerosol can, 12 oz. net wt., 6 oz. aerosol can, 5 oz. net wt.

View Permatex® Belt Dressing & Conditioner SDS HERE

View Permatex® Belt Dressing & Conditioner Product Information HERE

Permatex® Black Plastic Welder™

Epoxy & Adhesives

Features and Benefits:

Permatex’s Black Plastic Welder™ forms a tough durable bond to hard and semi-flexible plastics, aluminium, fiberglass and more. This structural adhesive designed for general purpose bonding of a wide variety of materials. Black in colour, ideal for automotive trim, bumper and clip needs.

Can be drilled, threaded, machined or painted once cured
Resists weather, high humidity and temperature vibrations
Ideal for automotive trim, bumper and clips needs
No-sagging, no clamp formula, UV Stable
Sets in 5 minutes/ Cures in 10 minutes
PSI Strength: 3,500

Automobile
Suggested Applications: Bonds rigid materials including ABS, Fiberglass, PVC, Vinyl, FRP, Acrylic, Glass, Styrene, Wood, and SMC.

No directions available.

View Permatex® Black Plastic Welder™ Part One SDS Here

View Permatex® Black Plastic Welder™ Part Two SDS Here

View Permatex® Black Plastic Welder™ Product Information Here

Permatex® Black Rubber Sealant

Sealants

Features and Benefits:

High-strength, ready-to-use automotive sealant insulates, seals and caulks. Does not dry out or become brittle. Economical black sealant.

DIRECTIONS:

Clean and dry surface to be repaired or sealed.
For best results, roughen smooth surfaces with coarse sandpaper.
Apply Black Rubber Sealant. Do not apply to exposed painted surfaces.
Black Rubber Sealant cures in about two hours. Dries fully in about 24 hours.
Use lacquer thinner (not on painted surfaces) to remove excess from hands or repair surface. Then wash hands with soap and water or use Permatex® Fast Orange® Hand Cleaner

Automobile
Suggested Applications: Weather stripping, door and window glass, and electrical connections.

View Permatex® Black Rubber Sealant SDS Here

View Permatex® Black Rubber Sealant Product Information Here

Permatex® Black Silicone Adhesive Sealant

Sealants

Features and Benefits:

Low odour formula! General-purpose, black RTV indoor/outdoor sealant. Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl, weather stripping and vinyl tops. Protects and repairs electrical wiring. May be applied to horizontal or vertical surfaces. Waterproof and flexible. Temperature range -59°C to 232°C (-75°F to 450°F); resists water, weather, and vibration.

DIRECTIONS:

Clean and dry all surfaces.
Cut nozzle to desired bead size, apply to one surface and assemble immediately.
Surfaces being bonded may need clamping for 1 hour or until silicone is firm.
Silicone”skins” and becomes tack free in one hour. Allow 24 hours for full cure and maximum strength under normal conditions. Allow more time in cold or very dry conditions.Trim excess with a sharp knife after cure. Most paint will not adhere to silicone. Surfaces should be painted first, then sealed.
Clean uncured silicone from hands, tools and clothing with Fast Orange® Hand Cleaner.

Automobile
Suggested Applications: Door frames, electrical connections, seams and roofs, vinyl tops, weather stripping (Not recommended for engine gasket applications).

Marine
Suggested Applications: Windshields, hatches, electrical connections, seams and
roofs, vinyl tops, weather stripping.

Package Sizes: 3 oz. tube, 12.9 oz. cartridge

View Permatex® Black Silicone Adhesive Sealant SDS Here

View Permatex® Black Silicone Adhesive Sealant Product Information Here

Permatex® Ceramic Extreme Brake Parts Lubricant

Lubricants

Features and Benefits:

A 100% synthetic formula, coupled with real ceramic solids make this premium brake lubricant our longest lasting, most temperature resistant way to silence brake noise. Effective from -50°F to 3000°F (-46°C to 1649°C), this product maintains its lubricating integrity under the most extreme conditions. Resistant to corrosion and contaminants, it will not wash out. For metal-to-metal contact only. For metal-to-metal contact only.

DIRECTIONS:

Clean parts to be lubricated with Permatex^® Brake & Parts Cleaner.
Apply small amount to caliper hardware and backing plates to create uniform surface areas and prevent noise.
Lubricant may also be used as a noise suppressor to eliminate caliper brakesqueal by applying to the BACK of the brake pad.

DO NOT APPLY TO ANY BRAKING SURFACES.

Automobile:

Suggested Applications: Caliper pins, hardware, and the back-side of brake pads.

Motorcycle:

Suggested Applications: Guide pins, disc brake pad

Package Sizes: 8 fl. oz. brush-top bottle, 5 fl. oz. tube carded

View Permatex® Ceramic Extreme Brake Parts Lubricant SDS HERE

View Permatex® Ceramic Extreme Brake Parts Lubricant Product Information HERE

Your Cart

PERMATEX